PENNEL & FLIPO

Shearing test

after 7 days > 80° C : 80 daN / 15cm²

Peeling test

after 7 days >20 °C: 18 daN/5cm
after 7 days >70 °C: 8 daN/5cm

DESCRIPTION :

This glue developed especially for the bonding of Neoprene and Neoprene CSM water resistant materials, as used for inflatable dinghies. It also serves as a suitable bonding agent for various types of rubber composites, such as SBR and Neoprene/metal. When applying this glue, add 5% to 10% DESMODUR RFE or ORCA® Hardener RFE according to the amount of ORCA® GLUE used. From 10 liters of mixed product, it is possible to improve the pot life of the adhesive reducing the quantity of hardener to 5% in volume only.


	Average Characteristics
	Base		Polychloroprene
	Color		Light cream
	Viscosity		Approximately 2200 mPa.S
	Dry Extract		Approximately 24%
	Density		0,89
	Inflammability		Flash point below 24°C – inflammable
	Storage		For 12 months in its sealed original packaging in a warm (+18°C) well ventilated environment
	Cleanning Solvent		NEOPRENE SOLVENT – N DILUENT

INSTRUCTION FOR USE :

Preparation of surfaces :

Inflatable boats: clean using NR SOLVENT or rub-down using fine emery paper. Then, apply ORCA® GLUE immediately maximum 1 hour after buffing. Rubber/metal compounds: clean or rub-down the surfaces.

Gluing :

Firstly, add an appropriate amount of DESMODUR (5% to 10% of total volume) to the glue and stir until fully mixed. Then, using a suitable paint brush, apply two coats of glue to both the surfaces



	Coat 1		Leave to dry for 10 minutes
	Coat 2		15 minutes according to room temperature and type material
	Open Time		30 minutes to 1 hour maximum according to room temperature and relative humidity. Do not exceed 70%

Gluing Value :

During laboratory testing using sample materials, the following average results were obtained:

These values are given as examples only. Depending their composition, surfaces should either be cleaned or rubbed-down before the glue is applied.

It is advisable to make a number of tests in a suitable manner according to the composition and origin of the materials to be glued, in view of the fact that these factors can considerably affect the results obtained.


Containement : 25 liters containers - 16 per paletts 10 liters containers - 54 per paletts Datasheet Safety Datasheet

Dicover Pennel
			Universe
			Key points
			History
			Contacts
			Directions
			Recruiting
ORCA® Product Range
	ORCA® Inflatable Boats
		ORCA® Fabrics
		ORCA® Tech PU Fabrics
		ORCA® Marketing Tools
		Information Request
	ORCA® Accessories
		NAUTA®
			The flexible tank
			Portable fuel tank
			Holding tank
			Big capacity fuel tank
			Water tank
			Fittings
			Tips
		ORCA® Rubrail
		ORCA® Glue
		ORCA® Hardener RFE
		ORCA® Cleaner
		Information Request
	ORCA® Oil Booms
		Neoprene Coated fabrics
		PU coated fabrics
		PVC coated fabric
		ORCA® tube in line
		ORCA® permanent boom
		Information Request
	ORCA® Bellows
		Introduction
		ORCA® T5 range
		ORCA® T3 range
		ORCA® T Accessories
		Information Request
	ORCA® Tanks
		Information Request
	ORCA® Protection
		Industrial Aprons
		Information Request
	ORCA® Liferafts & Safety
		Information Request